The gate width of more than 4500 mm set omega profiles (rigid profiles in the joints of panels), which eliminates the deflection of sandwich panels. And finally: ordering the gates, pay attention to the quality of packaging. This is, believe me, no small thing. In high-quality products must be factory packaging, or potential damage to the gate, or loss of components during transportation is very high. In short, to paraphrase a classic, we can say that the gate everything should be fine: and veneer, and automation, and packaging.

What to choose? Automatic gates are different. Today has been a steady demand for sectional Gates, that is made of interconnected horizontal paneley.No someone can choose whole (panel): the opening is closed one solid, usually steel, with a shield. Gates may pull off to the side, climb up, swing open. Which is preferable, to solve the customer, ie you. Michael J. Bender will undoubtedly add to your understanding. Additional equipment: device management, security and accessories Controls Control gates can be carried out on the wire or by radio. There is an ordinary radio control, and security, ie with rolling code. Key rings come in two-and four-button. They can be, respectively, to control two or four devices. Wire management can be performed with the following devices: – key-switch to the protection of the cylinder (English key, as an ordinary lock, turn in one direction – to open in another – close) – keypad or simply button (installed inside the house or garage) – the code panel (kodonabornik) when dialing code opens or closes – any other device access control (card reader Touch Memory tablet, proximity or smart card reader, etc.).

Tools – construction, plumbing, carpentry – are necessary to us in the most unexpected moments. It happens so that the toolkit is a long time untouched, gradually rusting and losing needed to work quality. Consider the main types of care instruments. For example, to as long as possible to use a vise, you should avoid strong impact on this tool with a hammer and hitting chips in the spindle. In addition, you should not keep them too long and things to make a side clamp. Prevent the formation of rust on the tool helps periodic lubrication of the clutches of a small amount of engine oil.

Squares of wood requires frequent checks for accuracy. In the presence of a strictly rectangular board test tool is simple: to do with it hold a line on the left and the second – on the right. These two lines should coincide. Care mites involves lubrication of joints with oil. Wire cutters should not be used for cutting a wire made of steel. A tool such as a cycle must be kept free from rust and grease a small amount of oil. Honing one more cycle, the tool is clamped tisochkami and with a file attached to the corners of the direct form, and then leveled at the touchstone and remove burrs formed. Cutting-edge tool polish the touchstone of steel round, pre-smeared with oil.

Work touchstone of steel requires the utmost caution as it can easily break the thin edge of the tool. After completing the sharpening, need some time to spend on an edge without changing the pressure. Oil and grease should be a tool like clamp – in need of its thread and the spindle. With regard to a chisel, then its use cutting edge sent down (this is done To avoid dulling the blade). After using the tool needed to hang the blade down. If the chisel must be transported to another place of employment, the cutting edge must be secure with a cardboard sleeve, case or cover of a durable fabric. The handle of the tool skewer on the principle of file holder, and sharpen the same way as the plane – with the difference that the angles of the blade is left straight. Level – this is the tool that will cherish from exposure to water. Check the level on a perfectly flat surface by turning 180 degrees (in the proper level of an air bubble in the glass tube will remain in place). Cover such a joiner tool, as a workbench, requires careful handling. If carried out work related to more pollution, there enclose a piece of paper or cardboard, and if you want to batter and drill – a board. Whatever actions were not for the bench (chiselling, sawing, drilling, gluing, driving nails, painting, soldering), proper care cap tool – it is cleaned with any trace of her work. Periodically, the lid and a bench vise is impregnated with heated oil flax. Oil lubricated and steel screw. If you want to update the surface, their first . Skilled craftsmen do not leave without attention and bench focus: comb to score not by hammering, and the lower surface of its handle. When the gauge blunt blade for sharpening using a different tool – file. Another recommendation for the owners of the gauge – protect these Tools of the influence of moisture.

You can put a thin sheet of dsp – initially it will not be noticeable, but after a few months will be visible to the structure and configuration of the floor board under the dsp, and it . Linoleum can be set for 110 rubles – domestic, it is rubbed in places of intense cross-country for a couple of months, and can be a commercial for 290 rubles per meter. Lumber can be no ognebiozaschitoy handle, because underneath it is not checked. All these moments can easily hide in the preparation of the offer, but I believe they need to know they describe, and selectively tested. Up until the opening of sexes as early as ready-made modules. His ceiling structure similar to that of sex.

The most important thing – the top layer – it is a drum and sealed (for example, Guerlain) or hermetically welded. Further there are lags on 100 * 50 mm and above, they do not "carry" load such as is sex, but because of the thickness of the insulation may be large in size. Step between 900 mm. top and bottom of the lag fits discharged board. On top of 40 mm thick, the bottom of 25 mm.

The whole timber is processed ognebiozaschitoy. At the bottom layer of boards "Tabs" finishing the ceiling. Insulation is placed between the lag in polyethylene. The savings here could be due to – the quality of metal (zinc or thickness) and sealed (as in welding, so and during milling), processing, packing and step thickness lumber.